Re: [ECOS] Flash detection

["M.Eugenia G.Valdecasas" <valdecasas at isar-tec dot com>]

> The driver could not get your device to go into "identify" mode.
> This can happen for many reasons:
>   * FLASH is write protected (the "write" signal is not allowed)

The write signal is allowed, actually the flash enters the query mode 
and read ID mode succesfully. We have traced it with a logic state 
analyzer. we can see all this data string : 0x00890089, 0x00180018, 
0x00510051 and blah blah blah....
I can't understand why all the information is in the bus (apparently 
succesfull read query and ID process) but the driver is still saying 
that can't not recognise the device...


>   * You've configured the driver incorrectly.  You say that you have
>     2x16 FLASH - what does that mean [to you]?  Show us your
>     configuration lines from the driver include files.

Sorry, I didn't express it correctly... what I meant is that we have 
two devices in parallel to form a 32 bit path 

The configuration lines are:

in altair_strataflash.inl->

#define CYGNUM_FLASH_DEVICES     (2)
#define CYGNUM_FLASH_BASE        (0x00000000u)
#define CYGNUM_FLASH_BASE_MASK   (0xFE000000u) // 2 * 16Mb devices
#define CYGNUM_FLASH_WIDTH       (16)
#define CYGNUM_FLASH_BLANK       (1)

#define FLASH_P2V(x) ((volatile flash_t *)(((unsigned)(x) < 0x1000) ? \
                            ((unsigned)(x) | 0xa0000000) : \
                            (unsigned)(x)))






> Note: the iPAQ flash is 2 devices organized in parallel to form a
> 32 bit path.  It might be a good place to look for assistance.
>
> --
> Gary Thomas <gary@mlbassoc.com>
> MLB Associates



On 2003.11.10 16:20, Gary Thomas wrote:
> On Mon, 2003-11-10 at 07:29, M.Eugenia G.Valdecasas wrote:
> > Hi, I recompiled redboot to use in our board. It has a PXA255
> processor
> > with 2x16 Intel 28F128J3 Flash. I use the strata flash drivers from
> > intel.
> > I upload redboot to the board with the JTAG tools but on starting
> comes
> > an error message:
> >
> >
> > +Can't identify FLASH, sorry, man e, dev 1e, id [<Not a string:
> > 0xA000CAFC>] stat 0
> > A000CAEC: 0E 1E B0 AB 0E 1E C0 AB  0E 1E D0 AB 0E 1E E0 AB
> > |................|
> > A000CAFC: 0E 1E F0 AB 00 00 00 00  00 00 00 00 00 00 00 00
> > |................|
> > A000CB0C: 00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00
> > |................|
> > A000CB1C: 00 00 00 00
> > |....            |
> > FLASH: driver init failed: Unknown error
> >
> > I tried the possible solutions named on the mailing list, like in
> > strata.c change the line  "if ( (qp->manuf_code ==
> FLASH_Intel_code)"
> > for "if(1 ", to define CYGHWR_IO_FLASH_DEVICE_NOT_IN_RAM and to
> change
> > the CNT into a higher value. But I still get the same error and it
> does
> > not go on.
> >
> > Have anybody any ideas what is it happening?. I would really
> appreciate
> > any help. Thank you in advance,

--
Before posting, please read the FAQ: http://sources.redhat.com/fom/ecos
and search the list archive: http://sources.redhat.com/ml/ecos-discuss