Re: gdbserver error (getprotobyname)

["Martin M. Hunt" <hunt at redhat dot com>]

David,

I don't know what causes this; perhaps a problem with the getprotobyname() 
function on your board.

You could try bypassing that function call.  In this context it has no useful
function anyway. I don't know which sources you have, but try this patch 
or something similar.

Index: remote-utils.c
===================================================================
RCS file: /cvs/src/src/gdb/gdbserver/remote-utils.c,v
retrieving revision 1.7
diff -u -p -r1.7 remote-utils.c
--- remote-utils.c	2001/07/12 21:04:35	1.7
+++ remote-utils.c	2002/02/13 06:59:20
@@ -106,7 +106,6 @@ remote_open (char *name)
       int port;
       struct sockaddr_in sockaddr;
       int tmp;
-      struct protoent *protoent;
       int tmp_desc;
 
       port_str = strchr (name, ':');
@@ -135,10 +134,6 @@ remote_open (char *name)
       if (remote_desc == -1)
 	perror_with_name ("Accept failed");
 
-      protoent = getprotobyname ("tcp");
-      if (!protoent)
-	perror_with_name ("getprotobyname");
-
       /* Enable TCP keep alive process. */
       tmp = 1;
       setsockopt (tmp_desc, SOL_SOCKET, SO_KEEPALIVE, (char *) &tmp, sizeof (tmp));
@@ -146,7 +141,7 @@ remote_open (char *name)
       /* Tell TCP not to delay small packets.  This greatly speeds up
          interactive response. */
       tmp = 1;
-      setsockopt (remote_desc, protoent->p_proto, TCP_NODELAY,
+      setsockopt (remote_desc, IPPROTO_TCP, TCP_NODELAY,
 		  (char *) &tmp, sizeof (tmp));
 
       close (tmp_desc);		/* No longer need this */

-- 
Martin Hunt
GDB Engineer
Red Hat, Inc.

On Tuesday 12 February 2002 10:40 pm, David Jones wrote:
> Hi,
>   I am using gdbserver on a StrongArm board compiled
> for arm-linux.  On my Linux x86 host I am running
> gdb compiled to debug an arm-linux target.  Thanks
> to Bill Gatliff for helping me out with this.
>
> I can successfully debug a program if I use the serial
> port between the host and the target.  This is great!
>
> However when I try to use a network connection I get
> the following error:  (below is a trace of my commands)
>
> (target output)
> ----------------------------------------------------
> # ./arm-linux-gdbserver davesplace:90 hello
> Process hello created; pid = 180
> getprotobyname: No such file or directory.
> Exiting
>
> (host output)
> (gdb) target remote tuxscreen:90
> Remote debugging using tuxscreen:90
> Couldn't establish connection to remote target
> Remote communication error: Connection reset by peer.
> (gdb)
> #
> ----------------------------------------------------
>
> Has anyone seen this type of error (i.e. getprotobyname)?
>
>
> I start the gdbserver first as recommended by the GDB documentation.
>
> man getprotobyname shows:
> The getprotobyname() function returns a protoent structure for the  line 
> from /etc/protocols that matches the protocol name name.
>
> The /etc/protocols file is present on my StrongArm target.
>
> # more /etc/protocols
> # /etc/protocols:
> # $Id: protocols,v 1.1.1.1 2001/09/12 19:03:24 andersee Exp $
> #
> # Internet (IP) protocols
> #
> #       from: @(#)protocols     5.1 (Berkeley) 4/17/89
> #
> # Updated for NetBSD based on RFC 1340, Assigned Numbers (July 1992).
>
> ip      0       IP              # internet protocol, pseudo protocol number
> icmp    1       ICMP            # internet control message protocol
> igmp    2       IGMP            # Internet Group Management
> ggp     3       GGP             # gateway-gateway protocol
> ipencap 4       IP-ENCAP        # IP encapsulated in IP (officially ``IP'')
> st      5       ST              # ST datagram mode
> tcp     6       TCP             # transmission control protocol
> egp     8       EGP             # exterior gateway protocol
> pup     12      PUP             # PARC universal packet protocol
> udp     17      UDP             # user datagram protocol
> hmp     20      HMP             # host monitoring protocol
> xns-idp 22      XNS-IDP         # Xerox NS IDP
> rdp     27      RDP             # "reliable datagram" protocol
> iso-tp4 29      ISO-TP4         # ISO Transport Protocol class 4
> xtp     36      XTP             # Xpress Tranfer Protocol
> ddp     37      DDP             # Datagram Delivery Protocol
> idpr-cmtp       39      IDPR-CMTP       # IDPR Control Message Transport
> rspf    73      RSPF            #Radio Shortest Path First.
> vmtp    81      VMTP            # Versatile Message Transport
> ospf    89      OSPFIGP         # Open Shortest Path First IGP
> ipip    94      IPIP            # Yet Another IP encapsulation
> encap   98      ENCAP           # Yet Another IP encapsulation
> #
>
>
> By the way my StrongArm is a tuxscreen. (see www.tuxscreen.net)
>
> David