This is the mail archive of the
mailing list for the Cygwin project.
Re: rebaseall ate my homework (Windows 10 install, that is)?
- From: ht at inf dot ed dot ac dot uk (Henry S. Thompson)
- To: cygwin at cygwin dot com
- Date: Wed, 29 Jun 2016 09:31:24 +0100
- Subject: Re: rebaseall ate my homework (Windows 10 install, that is)?
- Authentication-results: sourceware.org; auth=none
- References: <f5bwpl9kn4h dot fsf at troutbeck dot inf dot ed dot ac dot uk> <f5boa6lkms8 dot fsf at troutbeck dot inf dot ed dot ac dot uk> <loom dot 20160629T082053-760 at post dot gmane dot org>
Achim Gratz writes:
> Henry S. Thompson <ht <at> inf.ed.ac.uk> writes:
>> I [just sent] setup.log.full, which I don't _think_ shows anything going
> You'll have to find out why rebase gets into your Windows system directory.
> Check which files in /var/cache/rebase have these
None of them do :-(.
> and what the content of /var/lib/rebase/* is.
Just perl and python in dynbase.d, pointing to /usr/lib/perl5/site_perl
and /usr/lib/python2.7/site-packages respecively.
> When you say "reinstall", was that a clean install into a new "C:\C64"
To be careful and clear, the _first_ time the problem happened (i.e.,
Windows became unusable after a reboot), was after a normal run of
setup-x86_64 which updated Cygwin to 2.5.2. The subsequent timeline
Reinstall Windows 10, preserving partitions/files
(this works for some time, as do Cygwin tools after I add
/c/C64/bin to my PATH. A number of reboots, w/o difficulty)
Run setup-x86_64, pointing to local disk for packages and installing
into C:\C64, and downgrade Cygwin to 2.5.1 (only because setup didn't offer to
reinstall 2.5.2). No other packages installed.
(again, this works for a while)
First reboot fails, Windows is unusable
My suspicions are aroused that the 2.5.2 / 2.5.1 installs are causing
the problem, just because of the proximity of the failures
Reinstall Windows 10 _again_, again preserving partitions/files
Immediately run setup, reinstall 2.5.1 (again, from local disk and to
C:\C64) and reboot
Windows is unusable
> or did you try to install over an older installation?
So I never changed my Cygwin install directory, as I wanted to keep my
(large) home directory in play
> If the latter, did you perhaps link into the Windows systems directory
> from somewhere inside your Cygwin installation?
I don't _think_ so. What kind of link (cygwin vs. windows) would have
even been able to confuse rebase?
> Also, you seem to have modified the cygpath prefix, which potentially
> might be the source of your problem.
I did that five years ago at least, and it's a modification many others
do as well, I believe, so not sure how that could explain things.
Thanks very much for suggestions, please keep them coming! As I guess
should be clear, I _can_ access my disk from the Windows recovery
console, and even run individual (Cygwin) programs, so further
archaeology is still possible.
Henry S. Thompson, School of Informatics, University of Edinburgh
10 Crichton Street, Edinburgh EH8 9AB, SCOTLAND -- (44) 131 650-4440
Fax: (44) 131 650-4587, e-mail: firstname.lastname@example.org
[mail from me _always_ has a .sig like this -- mail without it is forged spam]
Problem reports: http://cygwin.com/problems.html
Unsubscribe info: http://cygwin.com/ml/#unsubscribe-simple